Water Jet Cutting Metal Thickness

By Hambali 07 May, 2021

We have the capacity to cut from metal sheets up to a size of 4m by 2m. For example, you can cut two foot thick (0.6 m) sponge easily.practically speaking 2″ (5 cm) to 3″ (7.5 cm) thick steel is about the upper thickness limit for an abrasive waterjet.

Finishing up a big Claro Walnut slab for Dorset Custom

Metals at jetcut, we can cut any metal, from 0.5 mm to 170 mm thick to a best tolerance of 0.004”/0.1mm for the laser and 0.008/0.2mm for the water jet.

Water jet cutting metal thickness. Abrasive waterjets are ideally suited for tough and lucrative applications for any metal cutting. For soft materials, you can cut extremely thick pieces. Up to 100mm size :

In this process, water is pushed through a small orifice at high pressure allowing the water to cut through the metal. The term abrasive jet refers specifically to the use of a mixture of water and abrasive to cut hard materials such as metal, stone or glass, while the terms pure waterjet. For example, you can cut two foot thick (0.6 m) sponge easily.

Laser & water jet cutting: For soft materials, you can cut extremely thick pieces. Pure waterjet is used for cutting softer materials, including gasket, foam, food, paper, plastic and carpet.

Water jet cutting maximum thickness. Waterjet abrasives are typically made of garnet, with grit size ranging from 50 to 220 mesh, though 80 is the most common. Waterjet cutting is used by metal processing specialists to form highly accurate cuts for custom metal components.

Abrasive waterjet is used to cut harder materials, such as metal, ceramic, stone, wood and glass. The water pressure is typically between 20,000 and 55,000 pounds per square inch (psi). In the food sector, for example, it is used for cutting cheese, fruit or vegetables.

The water jet uses garnet abrasive to cut virtually any hard material, with its superior 90,000 psi jet this flow water jet cutting machine can offer you quick, accurate superior cutting. Many users report cutting material even thicker than that. Waterjet cutting with pure water this method is primarily used for soft materials such as plastics, textiles, paper, sealing materials, metal foils, plywood, food, etc.

At all waterjet cutting we offer a complete and comprehensive range of metal cutting. Cutting thicker than that usually reduces the tolerance that can be maintained and increases the amount of time to cut a part. This also reduces the cutting width for pure water jet cutting to 0.08 mm and for abrasive water jet cutting to 0.2 mm.

Normal tap water is pressurised and forced through a small precious stone orifice, so that a highly powerful cutting jet is produced. More than just common materials of mild steel and aluminum, abrasive waterjets easily cut titanium, inconel®, brass, and tool steel. Up to 8 in and a 4 in bevel weight :

Other materials are carpets, textiles, fibrous materials or insulating materials. The actual cutting is often done under water to reduce splash and noise. Optimized also offer you water jet cutting for business.

Faster feed rates are used to prevent the jet from cutting all the way through. Practically speaking 2″ (5 cm) to 3″ (7.5 cm) thick steel is about the upper thickness limit for an abrasive waterjet. Water jet machining can be applied for cutting laminated glass fiber reinforced composite of thickness 5.0 mm with maximum feed rate of 6.0 m/min setting wjm process parameters such as water pressure of 3500 bar, nozzle diameter of 0.1 mm and nozzle tip distance of 2 mm [5].

The quality will begin to wain on anything above 1/2” in thickness. Because of its unique characteristics, the water jet cutter, delivers fine and accurate cut of up to 30 cm thick materials. The question begs to be asked,…

The water jet is known for cutting nearly any material type. Metal, for instance is easily cut using water jet cutting. Waterjet cutting uses a highly pressurized, focused stream of water—sometimes carrying an abrasive substance—to create precision cuts in metal and other materials.

Accuracies vary with material and thickness, but generally, we hold repeatable cuts with accuracies as close as ±0.003. Waterjets can cut any solid material including stone, tile, glass, metal, foam, rubber, plastic, and food. Thickness is also a factor in plasma’s cutting capabilities.

We specialise in cutting fibre cement, privacy screens, titanium, exotic metals, glass, ceramics, aluminium, stainless steel, brass, copper and rubber. West coast waterjet can produce parts as large as 3×4 meters, and can cut a variety of materials with. When it comes to cutting metal with water, west coast waterjet has some of the world’s most advanced capabilities.

Water jet cutting is a perfect tool for cutting high strength materials such as inconel, stainless steel, and titanium. Most abrasive waterjet cutting, however, is done in material that is 3 inches thick or less. Water jet cutting up 10” material.

Up to 4000mm x 3000mm with water cutting technology, the components are not heated, which is important in the processing of special steels and in cutting very complex configurations. The benefits of laser cutting include: Water jet cutters are used to cut through some of the toughest materials.

The water is forced through a 0.010 to 0.015 in diameter orifice (hole) in a jewel. From hardened steels to softer materials like wood, plastic and even food items like bread or cake, the water jet will have great success across the board. Plastic materials to be separated can be foils and seals.

Cv Supply Horse Stall Flooring, Horse Stall Mats, Equine

Gallery — Michael Wilson design Michael wilson, Design